Time Left - 35:00 mins
GATE 2021 ME : Toppers Quiz 15 (App update required to attempt this test)
Attempt now to get your rank among 708 students!
Question 1
Toggle position is defined as that position in a mechanism when ____.
Question 2
Which statement about impulse turbine is true?
Question 3
A shaft carrying 5 rotors will have following no. of nodes
Question 4
Choose the correct statement:
Question 5
Degree of freedom for rolling with slipping is?
Question 6
Air enters a compressor in a steady flow manner at 140 KPa and 17 °C and leaves it at 350 KPa and 127 °C. During the flow change in enthalpy and kinetic energy are 110.55 kJ/kg and 3.6 kJ/kg respectively. The minimum reversible work input required is ________ kJ/kg.
[Given: Environment temperature is 7 °C], R=0.28 kJ/kg·K
[Given: Environment temperature is 7 °C], R=0.28 kJ/kg·K
Question 7
A plane wall of 0.2m thickness and 25 W/m-K thermal conductivity is uniformly generating heat within the slab. The slab is exposed to a fluid at 92oC & the convection heat transfer coefficient between the wall and the fluid is 500 W/m2-K. If the uniform volumetric heat generation within the slab is 0.3 MW/m3, the maximum temperature in the wall is
Question 8
Optimal solution of any linear programming problem is always obtained from____.
Question 9
At point in a body stresses developed are such that σx= 140 MPa and σy = 60 MPa and the major principle stress is 150 MPa. What is the magnitude of max in-plane shear stress __________ (in MPa).
Question 10
The following table gives the information & data for the activities of a construction project
If indirect cost is Rs. 20/day, After crashing the project to minimum duration the total cost difference is ______Rs
Question 11
A crank and slotted lever mechanism with length of slotted arm as 600mm and length of fixed link as 200mm is used to transverse motion in a shaping machine. If the radius of the crank is 100mm length. Then find the stroke length of the slotted lever mechanism in mm
Question 12
When two gears are mating each other then which of the following statement about gearing profile is TRUE
Question 13
A single point cutting tool with 0°rake angle is used in an orthogonal machining process. At a cutting speed of 180 m/min. the thrust force is 490 N. If the coefficient of friction between the tool and the chip is 0.7, then the power consumption (in kW) for the machining operation is _______
Question 14
At a point in a material there are two direct stresses of 60 MPa tensile and 50 MPa compressive acting at right angles to each other. The greatest principal stress in the material is limited to 125 MPa in tension. What will be maximum shearing stress to which the material can be subjected on the given plane __________.
Question 15
Two castings of the same metal have the same surface area. One castings is in the form of a sphere and the other is a cube. What is the ratio of the solidification time for the sphere to that of the cube?
Question 16
The coordinate of the centre of the Mohr’s circle representing the pure shear stress condition will be
Question 17
According to maximum shear stress, the ratio of maximum shear stress to yield stress is equal to
Question 18
A fluid flowing over a flat plate has dynamic viscosity= 50 × 10-6 kg/ms , Specific heat= 1 kJ/kgK, Thermal conductivity, 0.05 W/mK, The hydrodynamic boundary layer thickness is 0.4 mm
The thermal boundary layer thickness is
Question 19
A single point cutting tool is designated as in ORS. The rake angle and principle cutting edge angle is
Question 20
Filler material is essentially used in __________.
- 708 attempts
- 3 upvotes
- 3 comments
Tags :
ESE & GATE MEGeneralApr 19ESE & GATE ME