Time Left - 35:00 mins
GATE 2021 ME : Toppers Quiz 18 (App update required to attempt this test)
Attempt now to get your rank among 727 students!
Question 1
If two gases having same initial conditions (P, V, T) are mixed in a container of volume ‘2V’ and temperature ‘T’, then the pressure of the mixture will be
Question 2
A cube strikes a stationary ball exerting an average force of 50 N over a time of 10 mili sec. The ball has mass of 0.20 kg. Its speed after the impact will be
Question 3
Which law of thermodynamics will be violated, if the thermal efficiency of an engine becomes 100%?
Question 4
A small ball of mass 1 kg moving with a velocity of 8 m/s undergoes a direct central impact with a stationary ball of mass 2 kg. the impact is perfectly elastic. The speed of 2 kg mass ball after the impact is _________.
Question 5
As per maximum shear stress theory of failure. The relation between yield strength in shear (𝜏𝑦) and yield strength in tension (σt) is __________.
Question 6
The feed of a tool with nose diameter = 4 mm, is 6 mm. Find peak to valley height ___________.
Question 7
A certain air has DBT 35oC and DPT of 20oC, the corresponding saturation pressure of water being 5.628 kPa and 2.33 kPa respectively. When the atmospheric pressure is assumed as 1.0132 bar, the specific humidity of air will be
Question 8
A heat pump operating on Carnot cycle pumps heat from a reservoir at 27°C to a reservoir at 327°C The coefficient of performance is :
Question 9
Modulus of resilience is the area under the curve of_____.
Question 10
Which cycle consists of two reversible isotherms and two reversible isobars?
Question 11
A bar made of ductile material is subjected to maximum and minimum stresses of 150N/mm2 and 50N/mm2 and has an endurance limit of 194N/mm2 and yield strength of 296N/mm2. The fatigue stress concentration factor is 1.The available factor of safety for this loading is
Question 12
A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm. Both bearing bore diameter and length are 40 mm. If radial clearance is and bearing is lubricated with an oil having viscosity 0.03 Pa.s, the Sommerfeld number of the bearing is ______
Question 13
A riveting machine is driven by a motor of 5 kW. The actual time to complete one riveting operation is 1.5s and it absorbs 10 kN-m of energy. The moving parts including the flywheel are equivalent to 200 kg at 0.5m radius of gyration. Speed of flywheel (in rad/s) after riveting, if it was 350 rpm before riveting will be
Question 14
A 20° full depth involute system have a pinion of diameter 300 mm and number of teeth on pinion is 60. If the length of line of action is 20 mm, then the contact ratio is _______.
Question 15
For an under damped system, if the ratio of two successive peak is 10, then the minimum damping ratio (ζ) will be
Question 16
For a statically determinate frame, which of the following is the correct graph between number of members and number of joints?
Question 17
What will be the tensile yield strength if the factor of safety is taken as 2. The values of principle stresses σ1 = 35 MPa andσ2 = -115 MPa were calculated from the Mohr’s circle. Use Maximum distortion energy theory.
Question 18
Which of the following is a false statement about work hardening?
Question 19
The natural frequency of the system in cycles/s is
Question 20
Which of the following assumption are taken during forming in slab method?
- 727 attempts
- 0 upvotes
- 3 comments
Tags :
ESE & GATE MEGeneralJan 21ESE & GATE ME